enable long file support, needed for boards using swspi and long filenames for firmware like mks robin 1.1/1.2
added MKS robin nano 1.2 board with description what and why
Signed-off-by: Leszek Zajac <zajc3w@gmail.com>
If switching a pin from output low to input with pullup, there is an
intermediate state of either driven high or high impedance without a
pullup. Similarly, when switching from output high to input without a
pullup, there is an intermediate state of either driven low or high
impedence with a pullup. In both cases it is preferable for the
latter transition.
Also, calculate the final setting prior to making any changes to
reduce the time in that intermediate state.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Don't leave the wires in a high output state during setup - leave them
in a high-impedance with pullup state.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The get_temp() code will stop reporting the last temperature of the
heater if there hasn't been any recent temperature updates. However,
on a full mcu communication loss this can cause the verify_heater code
to report a heating error prior to the mcu code reporting the
communication failure. Increase the heater timeout from 5 to 7
seconds to make it more likely the mcu failure is reported first.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
SHT3x would return a read NACK on host retries.
When the MCU receives the I2C CMD, it reads out data.
SHT3x clears the data buffer.
The MCU fails to deliver a response to the host.
The host retries, the device returns NACK,
then the MCU goes into the shutdown state.
Make sure there is at least 0.5s between retries.
Signed-off-by: Timofey Titovets <nefelim4ag@gmail.com>
Some devices can return a read NACK on host retries.
When the MCU receives the I2C CMD, reads out data,
but fails to deliver a response to the host.
The host retries, the device returns NACK,
and the MCU goes into the shutdown state.
Signed-off-by: Timofey Titovets <nefelim4ag@gmail.com>
Avoid using the name "config" as a local register storage variable as
it can be confused with the common "config" configfile reference.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Commit d120a313b incorrectly removed an assignment to self.config - in
this instance the reference was to a local variable not related to the
global configfile storage.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The more.musl.cc site is blocking downloads from all github actions,
which makes it difficult to use that site for the ar100 cross build
toolchain. Convert to the openrisc or1k-elf toolchain as a
replacement.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Update Code_Overview.md to note that the config object should not be
stored after the "config loading phase".
Remove a few inadvertent cases where a 'config' object was stored
in module member variables.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The rp2040 uses a pll vco divider of 6. Prefer setting postdiv1=6 and
postdiv2=1 (instead of the previous postdiv1=3 and postdiv2=2).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add a benchmark for the rp2350 device when running via CAN bus.
Remove the old stm32f042 CAN bus benchmark as that test predates a
number of importnat CAN bus code changes and is likely no longer
accurate.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Completely filling the spi transmit fifo could lead to a situation
where the rx fifo overflows. Make sure not to write past the rx fifo
size.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Completely filling the spi transmit fifo could lead to a situation
where the rx fifo overflows. Make sure not to write past the rx fifo
size.
Also, be sure to wait for the transmission to fully complete before
exiting spi_transfer().
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Avoid unnecessary (HAVE_STM32_CANBUS && MACH_STM32xx) checks in
Kconfig. The HAVE_STM32_CANBUS is a helper symbol for all the chips
that support canbus, there's no need to mix it with a check for a chip
that is already known to have canbus.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Validate host provided index prior to accessing memory using that
index.
Also, consistently use a uint8_t for max_sections (to account for
integer overflow issues).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add a filter workbench Jupiter notebook to help printer developers tune filters based on probing data
Signed-off-by: Gareth Farrington <gareth@waves.ky>
