mirror of
https://github.com/andreili/klipper.git
synced 2025-08-24 03:44:06 +02:00
6aec6efcc9
Introduce a CONFIG_USB build symbol that is set whenever CONFIG_USBSERIAL or CONFIG_USBCANBUS is set. Use that symbol during setup so that the USB controller is properly initialized for both usb serial and usb canbus bridge configurations. This fixes the clock configuration for usb canbus bridge mode on stm32f446. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
143 lines
3.5 KiB
Plaintext
143 lines
3.5 KiB
Plaintext
# Main Kconfig settings
|
|
|
|
mainmenu "Klipper Firmware Configuration"
|
|
|
|
config LOW_LEVEL_OPTIONS
|
|
bool "Enable extra low-level configuration options"
|
|
default n
|
|
help
|
|
Enable low-level configuration options that (if modified) may
|
|
result in a build that does not function correctly.
|
|
|
|
choice
|
|
prompt "Micro-controller Architecture"
|
|
config MACH_AVR
|
|
bool "Atmega AVR"
|
|
config MACH_ATSAM
|
|
bool "SAM3/SAM4/SAM E70 (Due and Duet)"
|
|
config MACH_ATSAMD
|
|
bool "SAMD21/SAMD51"
|
|
config MACH_LPC176X
|
|
bool "LPC176x (Smoothieboard)"
|
|
config MACH_STM32
|
|
bool "STMicroelectronics STM32"
|
|
config MACH_RP2040
|
|
bool "Raspberry Pi RP2040"
|
|
config MACH_PRU
|
|
bool "Beaglebone PRU"
|
|
config MACH_LINUX
|
|
bool "Linux process"
|
|
config MACH_SIMU
|
|
bool "Host simulator"
|
|
endchoice
|
|
|
|
source "src/avr/Kconfig"
|
|
source "src/atsam/Kconfig"
|
|
source "src/atsamd/Kconfig"
|
|
source "src/lpc176x/Kconfig"
|
|
source "src/stm32/Kconfig"
|
|
source "src/rp2040/Kconfig"
|
|
source "src/pru/Kconfig"
|
|
source "src/linux/Kconfig"
|
|
source "src/simulator/Kconfig"
|
|
|
|
# Generic configuration options for serial ports
|
|
config SERIAL
|
|
bool
|
|
config SERIAL_BAUD
|
|
depends on SERIAL
|
|
int "Baud rate for serial port" if LOW_LEVEL_OPTIONS
|
|
default 250000
|
|
help
|
|
Specify the baud rate of the serial port. This should be set
|
|
to 250000. Read the FAQ before changing this value.
|
|
|
|
# Generic configuration options for USB
|
|
config USBSERIAL
|
|
bool
|
|
config USBCANBUS
|
|
bool
|
|
config USB
|
|
bool
|
|
default y if USBSERIAL || USBCANBUS
|
|
config USB_VENDOR_ID
|
|
default 0x1d50
|
|
config USB_DEVICE_ID
|
|
default 0x614e
|
|
config USB_SERIAL_NUMBER_CHIPID
|
|
depends on USB && HAVE_CHIPID
|
|
default y
|
|
config USB_SERIAL_NUMBER
|
|
default "12345"
|
|
|
|
menu "USB ids"
|
|
depends on USB && LOW_LEVEL_OPTIONS
|
|
config USB_VENDOR_ID
|
|
hex "USB vendor ID" if USBSERIAL
|
|
config USB_DEVICE_ID
|
|
hex "USB device ID" if USBSERIAL
|
|
config USB_SERIAL_NUMBER_CHIPID
|
|
bool "USB serial number from CHIPID" if HAVE_CHIPID
|
|
config USB_SERIAL_NUMBER
|
|
string "USB serial number" if !USB_SERIAL_NUMBER_CHIPID
|
|
endmenu
|
|
|
|
# Generic configuration options for CANbus
|
|
config CANSERIAL
|
|
bool
|
|
config CANBUS
|
|
bool
|
|
default y if CANSERIAL || USBCANBUS
|
|
config CANBUS_FREQUENCY
|
|
int "CAN bus speed" if LOW_LEVEL_OPTIONS && CANBUS
|
|
default 500000
|
|
config CANBUS_FILTER
|
|
bool
|
|
default y if CANSERIAL
|
|
|
|
# Support setting gpio state at startup
|
|
config INITIAL_PINS
|
|
string "GPIO pins to set at micro-controller startup"
|
|
depends on LOW_LEVEL_OPTIONS
|
|
help
|
|
One may specify a comma separated list of gpio pins to set
|
|
during the micro-controller startup sequence. By default the
|
|
pins will be set to output high - preface a pin with a '!'
|
|
character to set that pin to output low.
|
|
|
|
# The HAVE_x options allow boards to disable support for some commands
|
|
# if the hardware does not support the feature.
|
|
config HAVE_GPIO
|
|
bool
|
|
default n
|
|
config HAVE_GPIO_ADC
|
|
bool
|
|
default n
|
|
config HAVE_GPIO_SPI
|
|
bool
|
|
default n
|
|
config HAVE_GPIO_I2C
|
|
bool
|
|
default n
|
|
config HAVE_GPIO_HARD_PWM
|
|
bool
|
|
default n
|
|
config HAVE_GPIO_BITBANGING
|
|
bool
|
|
default n
|
|
config HAVE_STRICT_TIMING
|
|
bool
|
|
default n
|
|
config HAVE_CHIPID
|
|
bool
|
|
default n
|
|
config HAVE_STEPPER_BOTH_EDGE
|
|
bool
|
|
default n
|
|
|
|
config INLINE_STEPPER_HACK
|
|
# Enables gcc to inline stepper_event() into the main timer irq handler
|
|
bool
|
|
depends on HAVE_GPIO
|
|
default y
|