Kevin O'Connor c95209bf7a atsam: ADC pins need to be in input mode with pullups disabled ...

The ADC pins (on at least the sam3x8e) need to be configured in input
mode with the internal pullups disabled in order to get accurate ADC
readings.

Reported by @bryanboettcher.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>

2019-08-28 13:45:01 -04:00

..

atsam

atsam: ADC pins need to be in input mode with pullups disabled

2019-08-28 13:45:01 -04:00

atsamd

armcm_link: Rename armcm_boot.lds.S to armcm_link.lds.S

2019-08-22 13:18:24 -04:00

avr

avr: Simplify spi mode setting

2019-05-07 23:02:20 -04:00

generic

armcm_link: Rename armcm_boot.lds.S to armcm_link.lds.S

2019-08-22 13:18:24 -04:00

linux

spicmds: Rework spi config commands

2019-08-06 18:56:53 -04:00

lpc176x

armcm_link: Rename armcm_boot.lds.S to armcm_link.lds.S

2019-08-22 13:18:24 -04:00

pru

pru: The TMR_CNT is cleared by writing all ones

2019-03-31 13:48:50 -04:00

simulator

simulator: Wrap code to 80 columns

2019-02-27 14:20:15 -05:00

stm32

armcm_link: Rename armcm_boot.lds.S to armcm_link.lds.S

2019-08-22 13:18:24 -04:00

stm32f0

stm32f0: Remove trailing tab from Makefile

2019-07-21 21:49:22 -04:00

adccmds.c

adccmds: Run gpio_adc_setup() before oid_alloc()

2019-01-13 11:03:30 -05:00

basecmd.c

spicmds: Rework spi config commands

2019-08-06 18:56:53 -04:00

basecmd.h

spicmds: Rework spi config commands

2019-08-06 18:56:53 -04:00

buttons.c

buttons: initialize mcu buttons based on inverted state

2019-07-05 20:01:07 -04:00

byteorder.h

byteorder: Add a header file defining common byteswap functions

2018-05-21 09:44:40 -04:00

command.c

command: Wait to send ack until after processing commands

2018-05-28 10:43:40 -04:00

command.h

buildcommands: Match DECL_X names to the actual C macro names

2019-08-22 13:26:30 -04:00

compiler.h

compiler.h: Check if __aligned and __section macros are already defined

2016-06-13 23:18:59 -04:00

ctr.h

ctr: Encode negative integers in normal hex notation

2019-08-22 13:06:44 -04:00

debugcmds.c

debugcmds: Add support for reading/writing 32bit values

2019-02-07 11:50:14 -05:00

endstop.c

endstop: Rename mcu end_stop commands to endstop

2019-07-12 08:10:53 -04:00

gpiocmds.c

gpiocmds: Specify soft pwm duration in clock ticks

2019-05-26 11:09:32 -04:00

i2ccmds.c

bus: Change bus parameter in config_spi/config_i2c

2019-04-04 18:29:31 -04:00

initial_pins.c

initial_pins: Add ability to configure output pins at mcu startup

2019-03-17 20:56:25 -04:00

initial_pins.h

initial_pins: Add ability to configure output pins at mcu startup

2019-03-17 20:56:25 -04:00

Kconfig

stm32: Rename stm32f4/ directory to stm32/

2019-08-05 11:25:40 -04:00

lcd_hd44780.c

lcd_hd44780: Add micro-controller code for the HD44780 LCD chip

2018-03-06 11:30:34 -05:00

lcd_st7920.c

lcd_st7920: Add brief delay around gpio toggle calls on fast MCUs

2019-08-10 11:45:15 -04:00

Makefile

initial_pins: Only build when CONFIG_HAVE_GPIO is enabled

2019-07-24 01:09:45 -04:00

neopixel.c

neopixel: Rework timing so that it works on AVR micro-controllers

2019-08-07 15:37:05 -04:00

pwmcmds.c

pwmcmds: allow 16-bit resolution

2019-04-05 19:02:48 -04:00

sched.c

sched: Force sched_try_shutdown to be inlined

2018-10-13 11:47:00 -04:00

sched.h

pru: Support config_reset command to manually reset mcu

2017-09-03 23:16:38 -04:00

spi_software.c

spi_software: Remove unused include file

2019-08-17 13:49:03 -04:00

spi_software.h

spi_software: Implementation of software spi

2019-02-13 11:52:20 -05:00

spicmds.c

spicmds: Rework spi config commands

2019-08-06 18:56:53 -04:00

spicmds.h

spicmds: Rework spi config commands

2019-08-06 18:56:53 -04:00

stepper.c

stepper: Don't update SF_LAST_DIR if SF_NEED_RESET

2019-07-12 07:54:24 -04:00

stepper.h

stepper: Introduce stepper_get_position command and remove from endstop.c

2017-03-09 14:54:52 -05:00

thermocouple.c

thermocouple: Define thermocouple types using enumerations

2019-03-17 19:38:18 -04:00

tmcuart.c

pins: Add support for pull down resistors

2019-02-27 11:13:21 -05:00