Kevin O'Connor 121249c999 stm32: Revert "stm32: performance improvement for spi on stm32f0" ...

This reverts commit a2c309a2b02d16ec15fee5702463621239261266.

The above commit is causing crashes on the stm32f103xb chip when spi
is in use.  It's unclear what the cause of the regression is, but the
optimization isn't required so revert it until the root cause can be
determined.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>

2020-03-04 18:33:34 -05:00

..

atsam

atsam: Fix typo causing chipid to not be fully read

2019-11-27 14:33:20 -05:00

atsamd

atsamd: Enable chipid as usb serial number

2019-11-25 19:30:31 -05:00

avr

avr: implement i2c_read

2020-01-13 22:29:50 -05:00

generic

usb_cdc: Report MCU type on all boards

2019-11-26 08:45:20 -05:00

linux

linux: implement i2c

2020-01-13 22:29:50 -05:00

lpc176x

lpc176x: Add support for ssp1 (#2393)

2020-01-14 22:06:29 -05:00

pru

pru: The TMR_CNT is cleared by writing all ones

2019-03-31 13:48:50 -04:00

simulator

simulator: Wrap code to 80 columns

2019-02-27 14:20:15 -05:00

stm32

stm32: Revert "stm32: performance improvement for spi on stm32f0"

2020-03-04 18:33:34 -05:00

adccmds.c

adccmds: Run gpio_adc_setup() before oid_alloc()

2019-01-13 11:03:30 -05:00

basecmd.c

basecmd: No need for finalize_config command to send "config" response

2020-02-20 12:01:21 -05:00

basecmd.h

spicmds: Rework spi config commands

2019-08-06 18:56:53 -04:00

buttons.c

buttons: initialize mcu buttons based on inverted state

2019-07-05 20:01:07 -04:00

byteorder.h

byteorder: Add a header file defining common byteswap functions

2018-05-21 09:44:40 -04:00

command.c

command: Wait to send ack until after processing commands

2018-05-28 10:43:40 -04:00

command.h

buildcommands: Match DECL_X names to the actual C macro names

2019-08-22 13:26:30 -04:00

compiler.h

compiler.h: Check if __aligned and __section macros are already defined

2016-06-13 23:18:59 -04:00

ctr.h

ctr: Encode negative integers in normal hex notation

2019-08-22 13:06:44 -04:00

debugcmds.c

debugcmds: Add support for reading/writing 32bit values

2019-02-07 11:50:14 -05:00

endstop.c

endstop: Rename mcu end_stop commands to endstop

2019-07-12 08:10:53 -04:00

gpiocmds.c

gpiocmds: Specify soft pwm duration in clock ticks

2019-05-26 11:09:32 -04:00

i2ccmds.c

avr: implement i2c_read

2020-01-13 22:29:50 -05:00

initial_pins.c

initial_pins: Add ability to configure output pins at mcu startup

2019-03-17 20:56:25 -04:00

initial_pins.h

initial_pins: Add ability to configure output pins at mcu startup

2019-03-17 20:56:25 -04:00

Kconfig

stm32f0: Remove hal based stm32f0 implementation

2020-01-14 17:08:01 -05:00

lcd_hd44780.c

lcd_hd44780: Minor change to timing delays

2019-11-26 09:49:43 -05:00

lcd_st7920.c

lcd_st7920: Add brief delay around gpio toggle calls on fast MCUs

2019-08-10 11:45:15 -04:00

Makefile

initial_pins: Only build when CONFIG_HAVE_GPIO is enabled

2019-07-24 01:09:45 -04:00

neopixel.c

neopixel: Rework timing so that it works on AVR micro-controllers

2019-08-07 15:37:05 -04:00

pwmcmds.c

pwmcmds: allow 16-bit resolution

2019-04-05 19:02:48 -04:00

sched.c

sched: Force sched_try_shutdown to be inlined

2018-10-13 11:47:00 -04:00

sched.h

pru: Support config_reset command to manually reset mcu

2017-09-03 23:16:38 -04:00

spi_software.c

spi_software: Remove unused include file

2019-08-17 13:49:03 -04:00

spi_software.h

spi_software: Implementation of software spi

2019-02-13 11:52:20 -05:00

spicmds.c

spicmds: Rework spi config commands

2019-08-06 18:56:53 -04:00

spicmds.h

spicmds: Rework spi config commands

2019-08-06 18:56:53 -04:00

stepper.c

stepper: Add some comments on s->position tracking

2020-03-04 14:30:41 -05:00

stepper.h

stepper: Introduce stepper_get_position command and remove from endstop.c

2017-03-09 14:54:52 -05:00

thermocouple.c

thermocouple: Define thermocouple types using enumerations

2019-03-17 19:38:18 -04:00

tmcuart.c

tmcuart: Fix typo in function name

2019-09-01 14:56:09 -04:00