Kevin O'Connor 917fd51057 stm32: Discard usbotg tx data until usb is ready ...

If the usb interface is not ready, just discard messages.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>

2019-08-30 12:15:45 -04:00

..

atsam

atsam: ADC pins need to be in input mode with pullups disabled

2019-08-28 13:45:01 -04:00

atsamd

armcm_link: Rename armcm_boot.lds.S to armcm_link.lds.S

2019-08-22 13:18:24 -04:00

avr

avr: Simplify spi mode setting

2019-05-07 23:02:20 -04:00

generic

armcm_link: Rename armcm_boot.lds.S to armcm_link.lds.S

2019-08-22 13:18:24 -04:00

linux

spicmds: Rework spi config commands

2019-08-06 18:56:53 -04:00

lpc176x

armcm_link: Rename armcm_boot.lds.S to armcm_link.lds.S

2019-08-22 13:18:24 -04:00

pru

pru: The TMR_CNT is cleared by writing all ones

2019-03-31 13:48:50 -04:00

simulator

simulator: Wrap code to 80 columns

2019-02-27 14:20:15 -05:00

stm32

stm32: Discard usbotg tx data until usb is ready

2019-08-30 12:15:45 -04:00

stm32f0

stm32f0: Remove trailing tab from Makefile

2019-07-21 21:49:22 -04:00

adccmds.c

adccmds: Run gpio_adc_setup() before oid_alloc()

2019-01-13 11:03:30 -05:00

basecmd.c

spicmds: Rework spi config commands

2019-08-06 18:56:53 -04:00

basecmd.h

spicmds: Rework spi config commands

2019-08-06 18:56:53 -04:00

buttons.c

buttons: initialize mcu buttons based on inverted state

2019-07-05 20:01:07 -04:00

byteorder.h

byteorder: Add a header file defining common byteswap functions

2018-05-21 09:44:40 -04:00

command.c

command: Wait to send ack until after processing commands

2018-05-28 10:43:40 -04:00

command.h

buildcommands: Match DECL_X names to the actual C macro names

2019-08-22 13:26:30 -04:00

compiler.h

compiler.h: Check if __aligned and __section macros are already defined

2016-06-13 23:18:59 -04:00

ctr.h

ctr: Encode negative integers in normal hex notation

2019-08-22 13:06:44 -04:00

debugcmds.c

debugcmds: Add support for reading/writing 32bit values

2019-02-07 11:50:14 -05:00

endstop.c

endstop: Rename mcu end_stop commands to endstop

2019-07-12 08:10:53 -04:00

gpiocmds.c

gpiocmds: Specify soft pwm duration in clock ticks

2019-05-26 11:09:32 -04:00

i2ccmds.c

bus: Change bus parameter in config_spi/config_i2c

2019-04-04 18:29:31 -04:00

initial_pins.c

initial_pins: Add ability to configure output pins at mcu startup

2019-03-17 20:56:25 -04:00

initial_pins.h

initial_pins: Add ability to configure output pins at mcu startup

2019-03-17 20:56:25 -04:00

Kconfig

stm32: Rename stm32f4/ directory to stm32/

2019-08-05 11:25:40 -04:00

lcd_hd44780.c

lcd_hd44780: Add micro-controller code for the HD44780 LCD chip

2018-03-06 11:30:34 -05:00

lcd_st7920.c

lcd_st7920: Add brief delay around gpio toggle calls on fast MCUs

2019-08-10 11:45:15 -04:00

Makefile

initial_pins: Only build when CONFIG_HAVE_GPIO is enabled

2019-07-24 01:09:45 -04:00

neopixel.c

neopixel: Rework timing so that it works on AVR micro-controllers

2019-08-07 15:37:05 -04:00

pwmcmds.c

pwmcmds: allow 16-bit resolution

2019-04-05 19:02:48 -04:00

sched.c

sched: Force sched_try_shutdown to be inlined

2018-10-13 11:47:00 -04:00

sched.h

pru: Support config_reset command to manually reset mcu

2017-09-03 23:16:38 -04:00

spi_software.c

spi_software: Remove unused include file

2019-08-17 13:49:03 -04:00

spi_software.h

spi_software: Implementation of software spi

2019-02-13 11:52:20 -05:00

spicmds.c

spicmds: Rework spi config commands

2019-08-06 18:56:53 -04:00

spicmds.h

spicmds: Rework spi config commands

2019-08-06 18:56:53 -04:00

stepper.c

stepper: Don't update SF_LAST_DIR if SF_NEED_RESET

2019-07-12 07:54:24 -04:00

stepper.h

stepper: Introduce stepper_get_position command and remove from endstop.c

2017-03-09 14:54:52 -05:00

thermocouple.c

thermocouple: Define thermocouple types using enumerations

2019-03-17 19:38:18 -04:00

tmcuart.c

pins: Add support for pull down resistors

2019-02-27 11:13:21 -05:00