Kevin O'Connor 0d8ddcadbb toolhead: Improve tracking of print_stall ...

The previous code increases print_stall if a move is proactively
flushed due to buffer_time_low and a follow up move is ready to send
before the existing moves are fully retired.  However, this would not
track the case where a move is proactively flushed and it takes an
extended amount of time to get sufficient moves to refill the queue.

Change the code so that print_stall increases anytime a new move is
queued after a proactive flush and there are existing moves not yet
fully retired.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>

2018-01-12 16:56:31 -05:00

..

cartesian.py

homing: Handle speed rounding when homing speed greater than max_velocity

2017-12-20 14:41:20 -05:00

chelper.py

klippy: Avoid using '%' syntax when calling logging module

2017-09-27 12:38:20 -04:00

chipmisc.py

chipmisc: Enable replicape steppers dynamically

2018-01-10 19:30:57 -05:00

clocksync.py

clocksync: The clock estimate should add the rtt time not subtract it

2017-12-16 20:21:38 -05:00

console.py

pins: Check if the same pin is referenced via different aliases

2018-01-10 19:26:06 -05:00

corexy.py

homing: Handle speed rounding when homing speed greater than max_velocity

2017-12-20 14:41:20 -05:00

delta.py

homing: Handle speed rounding when homing speed greater than max_velocity

2017-12-20 14:41:20 -05:00

extruder.py

extruder: Fix pressure advance on tiny moves with over extrusions

2018-01-08 14:39:19 -05:00

fan.py

mcu: Allow both shutdown and startup values to be set for output pins

2017-12-18 20:45:00 -05:00

gcode.py

gcode: Add support for M221 (set extrude factor) g-code command

2018-01-03 17:12:31 -05:00

heater.py

heater: Report PID tuning results via the g-code terminal

2018-01-10 22:58:12 -05:00

homing.py

homing: Handle speed rounding when homing speed greater than max_velocity

2017-12-20 14:41:20 -05:00

klippy.py

gcode: Move SET_SERVO command from gcode.py to chipmisc.py

2017-12-06 18:35:51 -05:00

list.h

Initial commit of source code.

2016-05-25 11:37:40 -04:00

mcu.py

pins: Check if the same pin is referenced via different aliases

2018-01-10 19:26:06 -05:00

msgproto.py

build: Add gcc and binutils version to mcu data dictionary

2017-12-21 20:32:10 -05:00

parsedump.py

build: Request python2 for all directly executed python binaries

2017-06-27 20:26:02 -04:00

pins.py

pins: Check if the same pin is referenced via different aliases

2018-01-10 19:26:06 -05:00

pyhelper.c

pyhelper: Fix GETHEX() macro used in dump_string() debugging

2017-05-17 09:57:09 -04:00

pyhelper.h

stepcompress: Modify check_expand() into check_push()

2017-04-07 19:05:04 -04:00

queuelogger.py

queuelogger: Add critical information to each logfile on rollover

2017-05-01 14:48:44 -04:00

reactor.py

reactor: Fix bug causing end() to not always work

2017-04-13 13:20:13 -04:00

serialhdl.py

build: Add gcc and binutils version to mcu data dictionary

2017-12-21 20:32:10 -05:00

serialqueue.c

serialqueue: Don't report sent_time on responses that are retransmitted

2017-09-30 19:37:20 -04:00

serialqueue.h

serialqueue: Rename clock estimation variable names

2017-06-30 20:15:36 -04:00

stepcompress.c

stepcompress: Fix proactive queue flushing on move with 64K+ steps

2017-11-29 20:24:50 -05:00

stepper.py

stepper: Automatically detect and handle shared stepper enable lines

2018-01-10 19:10:26 -05:00

toolhead.py

toolhead: Improve tracking of print_stall

2018-01-12 16:56:31 -05:00

util.py

klippy: Avoid using '%' syntax when calling logging module

2017-09-27 12:38:20 -04:00