Kevin O'Connor a285668b46 avr: Only prompt for cpu speed and uart port on LOW_LEVEL_OPTIONS ...

The cpu is almost always 16Mhz and the serial port is almost always
UART0, so no need to prompt in the normal case.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>

2019-02-16 08:23:00 -05:00

..

atsam

atsam: Fix hard pwm cycle divider calculation

2019-02-13 18:18:12 -05:00

atsamd

atsamd: Fix samd51 get_clock() sync bit check

2019-02-16 08:03:28 -05:00

avr

avr: Only prompt for cpu speed and uart port on LOW_LEVEL_OPTIONS

2019-02-16 08:23:00 -05:00

generic

armcm_timer: Add a generic timer mechanism for ARM CortexM3/M4 chips

2019-02-06 22:03:09 -05:00

linux

linux: Add support for bi-directional SPI communication

2018-07-24 11:16:05 -04:00

lpc176x

lpc176x: Convert code to use armcm_timer

2019-02-06 22:03:09 -05:00

pru

pru: Add wrappers for gpio_x_reset()

2018-08-27 12:45:01 -04:00

simulator

simulator: Fix simulator build

2019-01-25 18:23:27 -05:00

stm32f1

stm32f1: Convert code to use armcm_timer

2019-02-06 22:03:09 -05:00

adccmds.c

adccmds: Run gpio_adc_setup() before oid_alloc()

2019-01-13 11:03:30 -05:00

basecmd.c

basecmd: Rename get_status to get_clock

2018-05-29 10:57:29 -04:00

basecmd.h

pru: Support config_reset command to manually reset mcu

2017-09-03 23:16:38 -04:00

buttons.c

buttons: Clear pressed/last_pressed state on new buttons_query command

2018-10-01 12:40:28 -04:00

byteorder.h

byteorder: Add a header file defining common byteswap functions

2018-05-21 09:44:40 -04:00

command.c

command: Wait to send ack until after processing commands

2018-05-28 10:43:40 -04:00

command.h

command: Wait to send ack until after processing commands

2018-05-28 10:43:40 -04:00

compiler.h

compiler.h: Check if __aligned and __section macros are already defined

2016-06-13 23:18:59 -04:00

ctr.h

build: Avoid linker magic in compile_time_request.c unique id generation

2017-05-26 12:32:02 -04:00

debugcmds.c

debugcmds: Add support for reading/writing 32bit values

2019-02-07 11:50:14 -05:00

endstop.c

endstop: Eliminate end_stop_set_oversample command

2017-10-12 11:59:27 -04:00

gpiocmds.c

gpiocmds: Add update_digital_out command

2018-06-27 12:10:39 -04:00

i2ccmds.c

i2ccmds: Pass the i2c address as a 7-bit number (0-127)

2019-01-07 20:00:44 -05:00

Kconfig

atsamd: Initial support for SAMD51

2019-01-28 20:02:16 -05:00

lcd_hd44780.c

lcd_hd44780: Add micro-controller code for the HD44780 LCD chip

2018-03-06 11:30:34 -05:00

lcd_st7920.c

lcd_st7920: Use a longer delay at the start of each command/data

2018-06-22 23:47:09 -04:00

Makefile

spi_software: Implementation of software spi

2019-02-13 11:52:20 -05:00

pwmcmds.c

gpiocmds: Allow the start value for a pin to differ from the default_value

2017-10-12 11:59:27 -04:00

sched.c

sched: Force sched_try_shutdown to be inlined

2018-10-13 11:47:00 -04:00

sched.h

pru: Support config_reset command to manually reset mcu

2017-09-03 23:16:38 -04:00

spi_software.c

spi_software: Implementation of software spi

2019-02-13 11:52:20 -05:00

spi_software.h

spi_software: Implementation of software spi

2019-02-13 11:52:20 -05:00

spicmds.c

spi_software: Implementation of software spi

2019-02-13 11:52:20 -05:00

spicmds.h

thermocouple: Add initial support for common SPI temperature sensing chips

2018-07-24 11:16:05 -04:00

stepper.c

stepper: Fix bug when using a non-zero CONFIG_STEP_DELAY on AVR

2019-01-11 12:04:03 -05:00

stepper.h

stepper: Introduce stepper_get_position command and remove from endstop.c

2017-03-09 14:54:52 -05:00

thermocouple.c

thermocouple: Minor fixes

2018-07-25 09:06:50 -04:00

tmcuart.c

tmc2208: Initial support for configuring TMC2208 drivers

2018-08-27 12:51:27 -04:00