Kevin O'Connor 544f8c1e85 stepper: Add a get_name() method to PrinterStepper ...

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>

2018-06-22 14:09:01 -04:00

..

__init__.py

klippy: Add support for dynamic loading of python modules

2018-01-28 12:19:26 -05:00

ad5206.py

spicmds: Rework SPI message transmission

2018-05-07 09:10:34 -04:00

adc_temperature.py

adc_temperature: Support defining custom sensors in the config file

2018-04-09 15:44:34 -04:00

bed_tilt.py

probe: Move code from bed_tilt and delta_calibrate into ProbePointsHelper

2018-05-20 11:41:07 -04:00

delta_calibrate.py

probe: Move code from bed_tilt and delta_calibrate into ProbePointsHelper

2018-05-20 11:41:07 -04:00

display.py

display: Allow the ST7920_DISPLAY parameter to be configured

2018-06-21 09:58:35 -04:00

fan.py

fan: Allow the fan shutdown_speed to be configured

2018-05-18 19:12:03 -04:00

gcode_macro.py

gcode_macro: Add the ability to define custom g-code macros

2018-05-25 12:40:06 -04:00

heater_bed.py

heater: Add PrinterHeaters class that stores all sensors and heaters

2018-04-04 23:13:53 -04:00

heater_fan.py

fan: Allow the fan shutdown_speed to be configured

2018-05-18 19:12:03 -04:00

homing_override.py

homing_override: Add axes config parameter

2018-06-11 20:41:18 -04:00

multi_pin.py

pins: Remove module level get_printer_pins() and setup_pin() functions

2018-04-04 12:26:39 -04:00

output_pin.py

output_pin: Fix SET_PIN max_val check

2018-06-05 09:12:31 -04:00

pid_calibrate.py

pid_calibrate: Make sure to unregister new control class on error

2018-04-06 11:39:24 -04:00

probe.py

Extras: Probing does reply with the z position where the probe triggers.

2018-06-13 22:34:25 -04:00

replicape.py

linux: Convert linux SPI code to use the generic spicmds.c code

2018-05-07 09:10:34 -04:00

servo.py

servo: Use new gcode.register_mux_command()

2018-05-20 12:40:10 -04:00

static_digital_output.py

static_digital_output: Add static_digital_output section to extras/

2018-03-17 13:06:51 -04:00

stepper_buzz.py

stepper_buzz: Convert to iterative solver

2018-06-20 09:26:10 -04:00

temperature_fan.py

temperature_fan: Fix issue 403 use max_speed

2018-06-19 11:51:07 -04:00

thermistor.py

thermistor: Add Honeywell 100K and MGB18 thermistor definitions

2018-04-30 16:08:17 -04:00

tmc2130.py

tmc2130: Allow the PWMCONF register to be configured

2018-05-25 11:38:27 -04:00

verify_heater.py

verify_heater: Disable when writing output to a debug file

2018-06-08 23:51:41 -04:00

virtual_sdcard.py

gcode: Raise an error if a duplicate command is registered

2018-05-20 13:08:22 -04:00

z_tilt.py

stepper: Add a get_name() method to PrinterStepper

2018-06-22 14:09:01 -04:00