Janar Sööt 005cbe157a menu: allow names in card content and simplify define single card decks ...

Signed-off-by: Janar Sööt <janar.soot@gmail.com>

2019-01-07 21:38:53 -05:00

..

display

menu: allow names in card content and simplify define single card decks

2019-01-07 21:38:53 -05:00

__init__.py

klippy: Add support for dynamic loading of python modules

2018-01-28 12:19:26 -05:00

ad5206.py

ad5206: Use bus.py helper code for spi

2018-11-21 12:12:31 -05:00

adc_temperature.py

adc_temperature: Minor whitespace changes

2018-07-26 10:51:48 -04:00

bed_mesh.py

bed_mesh: Introduce fade_target option

2018-11-30 11:37:21 -05:00

bed_tilt.py

bed_tilt: Do not automatically run G28 on BED_TILT_CALIBRATE

2018-10-22 11:26:01 -04:00

bltouch.py

bltouch: Issue both a "reset" and a "pin_up" after a successful probe

2018-12-16 11:06:46 -05:00

bus.py

i2ccmds: Pass the i2c address as a 7-bit number (0-127)

2019-01-07 20:00:44 -05:00

buttons.py

mcu: Rename add_config_object() to register_config_callback()

2018-09-03 11:48:22 -04:00

delta_calibrate.py

delta_calibrate: Do not automatically run G28 on DELTA_CALIBRATE

2018-10-22 11:26:01 -04:00

endstop_phase.py

tmc2660: Add endstop phase detection functionality to TMC2660 extra (#816)

2018-10-24 16:01:12 -04:00

fan.py

fan: Allow the fan shutdown_speed to be configured

2018-05-18 19:12:03 -04:00

force_move.py

force_move: Provide defaults for SET_KINEMATIC_POSITION parameters

2018-08-02 08:58:18 -04:00

gcode_macro.py

gcode_macro: Provide more information on a formatting error

2018-09-30 12:43:54 -04:00

heater_bed.py

heater: take a gcode_id when setting up a heater (#1028)

2019-01-02 17:44:02 -05:00

heater_fan.py

heater_fan: Allow multiple heaters to be defined for a heater_fan

2018-08-17 10:20:12 -04:00

homing_override.py

gcode: Rename run_script() to run_script_from_command()

2018-06-30 14:08:02 -04:00

idle_timeout.py

idle_timeout: Add printing/ready/idle tracking

2018-10-28 18:39:45 -04:00

mcp4451.py

i2ccmds: Pass the i2c address as a 7-bit number (0-127)

2019-01-07 20:00:44 -05:00

mcp4728.py

mcp4728: Add initial support for the mcp4728 i2c dac chip

2019-01-02 18:17:56 -05:00

multi_pin.py

pins: Explicitly pass can_invert and can_pullup to lookup_pin()

2018-07-26 09:44:45 -04:00

output_pin.py

output_pin: Fix SET_PIN max_val check

2018-06-05 09:12:31 -04:00

pid_calibrate.py

pid_calibrate: Add some comments on the calibration methodology

2018-10-19 22:40:11 -04:00

probe.py

bltouch: Add initial support for a bltouch "extras" module

2018-11-30 11:34:20 -05:00

quad_gantry_level.py

probe: Support manual probing at runtime

2018-10-01 11:12:30 -04:00

query_endstops.py

query_endstops: Move QUERY_ENDSTOP command to it own extras/ module

2018-07-16 10:06:30 -04:00

replicape.py

replicape: Use bus.py helper code for spi

2018-11-21 12:12:31 -05:00

respond.py

respond: An extra for sending messages to the printer host. (#1053)

2019-01-02 17:45:35 -05:00

servo.py

servo: This patch create ability to enable/disable attached servo. (#880)

2018-11-14 09:38:09 -05:00

spi_temperature.py

spi_temperature: Use bus.py helper code for spi

2018-11-21 12:12:31 -05:00

static_digital_output.py

static_digital_output: Add static_digital_output section to extras/

2018-03-17 13:06:51 -04:00

statistics.py

statistics: Move stats handling to new "extras" module

2018-09-02 13:46:19 -04:00

sx1509.py

i2ccmds: Pass the i2c address as a 7-bit number (0-127)

2019-01-07 20:00:44 -05:00

temperature_fan.py

temperature_fan: Fix issue 403 use max_speed

2018-06-19 11:51:07 -04:00

thermistor.py

thermistor: Avoid divide by zero error if min_temp=-273.15

2019-01-04 12:47:37 -05:00

tmc2130.py

tmc2130: Use bus.py helper code for spi

2018-11-21 12:12:31 -05:00

tmc2208.py

tmc2208: error raise fixed for rx/tx mcu check

2018-12-27 11:44:41 -05:00

tmc2660.py

tmc2660: error and whitespace fixes

2018-12-27 11:44:41 -05:00

verify_heater.py

verify_heater: Don't report a heater error if printer is shutdown

2018-09-30 10:40:44 -04:00

virtual_sdcard.py

gcode: process_batch() should execute commands atomically

2018-10-28 18:39:45 -04:00

z_tilt.py

z_tilt: Wrap lines to 80 columns

2018-10-01 11:12:30 -04:00